Peugeot 208 Key Replacement
It is best to leave the replacement of Peugeot keys 208 to auto locksmiths who have the right equipment and knowledge. They can make and program new keys quicker than a dealership and at a lower cost.
If the key fob stopped locking or unlocking your doors, it is likely due to a dead battery in the coin. There are other reasons why the key might be malfunctioning.
Dead Coin Battery
A dead coin battery can stop your Peugeot 208 from locking or unlocking, and will not start the engine. If this is the scenario, you'll need use the backup starting method that is detailed in the owner's manual for your vehicle.
The spark plugs can also be worn out. The spark plugs light the fuel to start the engine. They have a limited life span. They will eventually break down if they aren't used frequently enough.
There is a simple solution for this problem. The best option is to determine the voltage of your car battery with a multimeter. If it is below 11.5 Volts then you must replace it. If the battery has corroded it is essential to clean its contacts. This can be accomplished by removing the rubber cover from the two terminals on the battery and then using a wirebrush to remove any corroded battery parts. Then, you must reconnect the positive pole cables to the negative.
Water Damage
If your 208 won't start and the battery hasn't failed, you should examine the spark plugs. It could be that they are overly dirty, which causes them not to spark. The spark plugs can be cleaned in an workshop.
Peugeot automobiles use transponder keys that integrates with the car's immobiliser system. This ensures that only a valid key can turn the engine. If the chip inside the Peugeot key is damaged, then it will not send the correct signal to the vehicle.
Water damage is the most common cause of this issue. This is a frequent issue in more cold climates where the car is exposed to snow or rain. In this situation, contact a reliable locksmith who has the tools and equipment required to change the key's programming. They will also have the latest technology and machinery needed to make the Peugeot smart key. The process shouldn't take longer than 15 minutes.
Faulty Battery Contacts
Peugeot changed from the carbon-encased transponder chips to an entirely new type of chip that uses electronic components that are placed on a circuit board. This new technology works great when it's brand new, but over time the circuit boards start to lose their effectiveness and cease working properly.
This can stop the immobiliser chip from working which means that your car won't start. If this is the case it's recommended to contact a Peugeot specialist or locksmith.
A common issue is when the battery inside the key fob begins to die. This causes the blade of the key to stop feeding into your lock. g28carkeys.co.uk can replace the battery and cut a new blade for you, it's usually a simple fix.
Faulty Receiver Module
It could be that the receiver module has a problem in the event that your Peugeot key fob isn't working after being dropped on the floor, or exposed to a stormy rainstorm, or accidentally washed. The receiver module is responsible for transmitting radio frequencies to the onboard computer which manages the central locking system of your Peugeot vehicle.
The rubber seals on the key fob keep water from reaching its electronic chip. The chip can be damaged by water in the event that it is exposed water for a long period of. The high salt content in the pool or ocean water can cause damage to the key fob if it is submerged.
If your Peugeot spare key fob stops working You'll need the module replaced. This is only performed by a professional auto locksmith or Peugeot specialist. As opposed to other cars, Peugeot keys are protected by an immobilizer that is unique and requires the correct code to begin the engine. This is why you should trust an experienced Peugeot locksmith with the task of designing and programming the replacement.
Computers with faulty on-board computers
The computer on board of your Peugeot is responsible for a variety of features in your car, including airbags and power windows. If something goes wrong with these systems, it will typically show a code that identifies the problem. This code is stored in the system and remains there until the issue is fixed. In most cases, this will require the on-board computer being replaced.
One of the main causes of the light flashing is loose or corroded connection in the airbag sensor. This can be caused by wear and tear, ageing, or exposure to moisture and salt. It is essential to have this issue resolved as soon as you can, as a malfunctioning airbag can be dangerous in the event of an accident.
If your Peugeot is showing a card that is not being detected error, then the key battery inside the key fob may be dead or weak. This could prevent the key fob from sending a signal to disable your vehicle's standard immobilizer. You can test this by pressing the unlock button on the key fob and then attempting to start your vehicle. If this doesn't work, then the key battery is in need of replacement.